Search Results

Outline of available printers menuIt includes a list of all available printersEach printer includes an image, and the make and model of each.It includes a connectivity indicator if the printer is connected (green dot) or disconnected (outline), and notice if h...

After starting the printer, use the touchscreen to click "Menu"On the left side of the screen, click "Settings"Scroll down and click "Restore Defaults"Click on "Restore Printer" and accept the promptThis will reset the printer to factory defaults.

Turn off the printer using the switch on the back. Press and hold FEED + PAUSE while turning on the printer.Continue holding FEED + PAUSE until the first control panel light turns off.The printer configuration is now reset to the factory default values.

ATTENTION: We suggest first performing the calibration from the website. If the calibration fails, then follow these steps.Step 1: Media CalibrationHold the PAUSE + CANCEL buttons for 2 seconds to start the media calibration.Step 2: RFID CalibrationPress the m...

ATTENTION: We suggest first performing the calibration from the website. If the calibration fails, then follow these steps.Step 1: Media CalibrationFirst, make sure media is properly loaded, the printer cover is closed, and printer power is ON.To perform a Med...

Desktop printersThese printers can easily be identified visually.Zebra ZD500R:Zebra ZD621R:Printronix T800 (T820, T830):Industrial PrintersThese printers can be harder to tell apart visually, however you can usually find the model number printed on the front a...

A “GAP NOT DETECTED” error means that the printer was not able to find the gap/mark between labels. There are a few potential causes for this error:The printer has not performed a media calibration on the labelsSolution: Calibrate your printer.The labels are n...

Updating the firmware on your TSL handheld reader can improve the performance of your scans, as well as ensuring you have important fixes that have been pushed by the manufacturer.If you are using Windows for ARM, you need to install extra drivers. Click here ...

To adjust the print darkness on your ZT411 printer, take the following steps: On the home screen of the printer, tap the Menu button Tap the Print icon, then Print Quality, then select the Darkness option Adjust the darkness setting using the slider or + ...

If you purchased a Printronix printer with Wi-Fi capabilities, follow these instructions to connect the printer to your network. This article assumes that your Wi-Fi network is protected by WPA Personal with an ASCII passphrase, which covers most cases. If yo...

From Shopify Admin, type "Simple RFID" in the search bar, then select Search "Simple RFID" in Shopify App Store.Click on Simple RFID Inventory Solution. You may see a few advertisements in the search results before our app.Next, click Install near the left sid...

From the web portal, click the Available Printers menu.Locate your printer, then click the Settings icon.Check the value for the Firmware property.At the time of writing, these are the latest firmware versions:T800 (T820, T830): V1.48ET4000 (T4204): V1.46HT600...

To use this upgrade method, your printer must be connected to your network. If a network connection is unavailable, update the firmware via a USB flash drive.Requirements:A device with a web browser, on the same network (LAN) as your printerThis device must be...

If you find that scans are appearing slowly, and or accuracy seems poor, you'll want to set the Reader power to the maximum output, and that the Reading Sensitivity is set to FarPrerequisites Pair the RFID readerNavigate to the Scan ViewScan ViewClick on the R...

Calibrate from the web portalCalibrate from the printer

Printronix printers often state "Job in Process" (often misread as "Job in Progress") on their screen, as shown below:This message indicates that the printer is processing data from the host. Since this includes periodic status checks and other information, th...

Printronix printers lock the Enter switch to prevent accidental changes to settings. If you see the ENTER SWITCH LOCKED message, just press the Up and Down arrow keys at the same time, and you should then see ENTER SWITCH UNLOCKED.

TSL readers' USB connection uses a Virtual COM port, which requires extra driver installations on Windows for ARM. These are the steps to install the drivers.Step 1: Install the bus layer driverFirst, plug the reader into your PC using the supplied USB cable.D...

Press the button under the HOME symbol.Use the left-right arrow keys to select TOOLS, then press ENTER.Use the left-right arrow keys to navigate to MANUAL CALIBRATION, then press START.The printer should now say LOAD BACKING, PRINTER PAUSED.Open the printer, r...